Any topics of general interest (not lada related), post them here.
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 4:50 pm
oops
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 5:05 pm
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 7:00 pm
wondered how the kids could put a nice big scratch in my new 21.6" widescreen flatpanel monitor
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 9:56 pm
That looks similar to the one i bought after i sold my motorola brick phone. Those brick phones were bulletproof!
Just finished replacing the flusher handle on the "head" after someone busted the old one. Which led into replacing the flapper valve and searching in the junk bin for new nuts to hold the tank on as the other ones were stripped.
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 10:10 pm
A couple more phones and you can qualify to open a kiosk at the shopping mall
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 09, 2008 10:15 pm
Maybe you can sell the world famous portable cell phone booths too
All i have now is my sanyo scp-7000. It has the best speakerphone i've ever used and it's rubberized case can take a beating in the truck.
http://www.tech-faq.com/sanyo-scp-7000-review.shtml
-
Alejoint
- Gold
- Posts: 1107
- Joined: Sat Feb 03, 2007 1:27 pm
- Location: Venezuela
Post
by Alejoint » Tue Nov 11, 2008 7:38 pm
Put a little over 300 more Km on the Bronco's odometer. Pipe's selling good...
-
BaZBaZ
Post
by BaZBaZ » Fri Nov 14, 2008 7:07 pm
Re-tensioned my timing chain, being as it was such a nice mild day today; now I can properly hear my exhaust system blowing, but it does run better again now ...
...
... VAZ Book has this to say -
...... Which I think is fair enough ......
Mullered my thumbnail (again !! only nearly grew back grrr ) when the socket slipped 'cos I'd overtightened the adjuster cap. Still, it isn't the one I suck, the thumb !!
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sat Nov 15, 2008 2:19 am
Installed some 8' X 16" shelving into my gutted basement to try and get rid of some of the mountain of STUFF lying around.
-
excossack
- Titanium with furry dice
- Posts: 6953
- Joined: Fri Jun 27, 2003 1:16 am
-
Contact:
Post
by excossack » Sun Nov 23, 2008 2:29 pm
Today i covered the wooden rear panels with some black vinyl, that i got off someone on this forum. It looks much better that plain old wood.
Regards.
John 2E0DHN
Holly: This is not a daffodil, repeat, this is not a daffodil!
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Tue Nov 25, 2008 9:36 pm
Got the sexy wife a new toy for an early christmas present... Get to try it out tomorrow.
It's the beginning of the end of human life as we know it
-
Alejoint
- Gold
- Posts: 1107
- Joined: Sat Feb 03, 2007 1:27 pm
- Location: Venezuela
Post
by Alejoint » Sat Nov 29, 2008 3:31 pm
Spent about 5 hours going up a rather steep learning curve designing this:
I'm having a major brainfart trying to figure out how to make it a 3D drawing...
-
Alejoint
- Gold
- Posts: 1107
- Joined: Sat Feb 03, 2007 1:27 pm
- Location: Venezuela
Post
by Alejoint » Sun Nov 30, 2008 5:49 am
Getting there:
-
crb247
- Diamond
- Posts: 2377
- Joined: Sun Feb 03, 2008 7:56 am
- Location: Sault Ste. Marie, Ontario, Canada
Post
by crb247 » Sun Nov 30, 2008 5:57 am
Hmmmmm.. vernier cam sprocket hub?
-
Alejoint
- Gold
- Posts: 1107
- Joined: Sat Feb 03, 2007 1:27 pm
- Location: Venezuela
Post
by Alejoint » Sun Nov 30, 2008 5:59 am
crb247 wrote:Hmmmmm.. vernier cam sprocket hub?
You sir, are correct!
Still have to find someone to do the machining.